PLUMBING 101: WHAT YOU MUST HAVE FOR INSTALLING A BATHTUB

Plumbing 101: What You Must Have for Installing a Bathtub

Plumbing 101: What You Must Have for Installing a Bathtub

Blog Article

Further Details

Each person maintains their own individual way of thinking about Installing A Bathtub.


A Step-by-Step Guide to Installing a Bathtub
Installing a bath tub isn't exactly rocket science, but it does call for strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably hard job. If the old tub is readily accessible, the task can relocate rapidly; if you need to open up a wall to get rid of the old bathtub as well as position the brand-new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will require a helper to move out the old tub and embeded in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable trying it. As opposed to employing a professional to take control of a halfway-completed project, it is much better to consider utilizing one prior to you start. Opportunities are you may need an expert plumber to make tube links.
This article will aid you mount a new tub in your restroom if you have actually already bought a new bathtub and don't require to change the setup of your previous water supply pipes.
Your devices and also product checklist must make up the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Removing Old Taps


    If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the water system. After doing so, turn on the taps to drain any water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome because of the restricted access that is frequently the instance.
    Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth all set for the continuing to be water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
    Prior to going on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end supplies a link to the existing supply pipelines.
    If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next, position the tap in the placing opening in the bath/basin ensuring that the washing machines remain in location in between the faucet as well as the sink. Secure the faucet in position with the producer offered backnut. Once the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal tap ports. The previous type must be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Installing the Bath tub


    Making use of the two wooden boards under its feet, place the tub in the required placement. The wooden boards are helpful in uniformly spreading the weight of the tub over the location of the boards rather than focusing all the weight onto 4 small factors.
    The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub until the spirit level reviews degree.
    To mount taps, fit the bottom of the outermost flexible tap adapter to the proper supply pipeline by making a compression join; after that do the exact same for the various other tap.
    Activate the water as well as examine all joints and brand-new pipework for leakages and tighten them if needed. Fill the tub as well as additionally examine the overflow outlet and the regular electrical outlet for leakages.
    Lastly, fix the bath paneling as described in the manufacturer's user's manual. Tiling and sealing around the bathtub should wait till the tub has actually been utilized at least when as this will certainly settle it right into its final placement.

    Getting ready for the Installation


    First of all, the sustaining framework provided with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the tap includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets system to prevent stress on the bathtub.
    Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the provided washers.
    Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its final setting.

    Tiling Around the Bathtub


    In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a stiff seal, creating the water to penetrate the wall between the bathroom and also the tiling, leading to complications with wetness and also feasible leaks to the ceiling below.
    You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water before securing, to permit the motion experienced when the tub remains in usage. The sealant can fracture relatively early if you do not think about this motion before securing.
    Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily available on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof sticky and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Installing A Bathtub

    We had been made aware of that write-up about How to Install a Bathtub through an associate on another web property. I beg you take the opportunity to distribute this page if you appreciated it. Many thanks for taking the time to read it.


    Overflow? We're here!

    Report this page